The laptop is a portable electronic device where battery life is a significant factor to look for. If there is no battery, then your laptop is no different from a desktop as you’ll always require a power supply. Most of the time, HP users come across a situation that their laptop is not charging despite being plugged into the power supply. This has become quite an annoying issue for which they can’t access anything from the device.
If you’re also having trouble while charging your HP laptop, then don’t worry. Though it can be serious, there are possible solutions that you can use to fix it properly. Let’s move on to the solutions you need to know to fix HP laptop plugged in not charging problem.
HP Laptop Plugged In Not Charging | Solve Using Effective Troubleshooting Methods
Due to multiple reasons, your laptop won’t charge. If there is any misalignment between the battery and charger, then such a problem may arise. Mostly, the battery drivers may become corrupted due to which you might face this error in your laptop. The charging issue can also be related to the BIOS configuration errors. Here are some of the effective methods you can use to eliminate this error from your laptop.
Solution 1: Unplug And Plug The Charger
Primarily you can try this method to see if there is any change in the situation. Unplug the charger and after a few seconds plug it back. It can solve your problem. This helps your laptop’s charging system to revamp and improves the alignment with the battery. As a result, your HP laptop will start charging properly.
Solution 2: Plug the Charger Without A Power Surge Protector
When you’re using a power surge protector, it will change the sinusoidal input of the power supply. For that, your laptop won’t be able to charge normally. Most devices are capable of identifying these irregularities and prevent supply from the power source to the battery. In order to stop this, you can try connecting your laptop directly to the socket without using any surge protector.
Solution 3: Discharge The Motherboard
- At first, shut down the system and then disconnect the external devices like keyboard, mouse, external hard drive, printer, etc. from your laptop.
- Detach the power supply from your laptop and remove the battery from it. In case your device doesn’t have a removable battery then you need to look for a tiny hole at the back. Once you find the hole, press and hold a paper clip there to simulate a removing battery.
- Now, you have to press and hold the power switch for about 20-30 seconds. It will drain the remaining charge from the laptop. You can try blowing out the dust particles from all the ports and holes of the laptop.
- After that, plug in the power cable to your laptop.
- When the system is on and booted correctly, then you can insert the battery again back to the laptop. Now, check whether the error is resolved.
Solution 4: Reset BIOS Settings
- To do change in the BIOS settings turn off the system.
- During this press the power button and press F2 or F10 instantly to open the BIOS settings window.
- Next, press F9 to load the defaults and F10 to accept the changes. Otherwise, exit from the window while saving the changes.
Solution 5: Uninstall and reinstall your ACPI-Compliant Control Method Battery Drivers
The battery drivers control the charging of your laptop when it boots into your Operating System. Uninstalling the driver will enable Windows to reinstall the correct drivers automatically. To do that follow the below procedure:
- Press both Windows and R from your keyboard while the charger is plugged to the laptop.
- Type ‘devmgmt.msc’ in the Run box and press Enter. Device Manager window will appear on your screen.
- Go to the Batteries and expand it. Under that, right-click on the ‘Microsoft ACPI Compliant Control Method Battery’ listing and then select Uninstall.
- A prompt will appear regarding confirmation. Click on OK to continue.
- After the uninstallation, take out the battery and wait for about 10 seconds. Next, put the battery back to its place in the laptop.
- Click ‘Scan for hardware changes’ from the Device Manager toolbar. Then, it will search your battery and reinstall the drivers in your system. When it’s over, restart your laptop and check if the battery is charging.
Solution 6: Update ACPI-Compliant Control Method Battery Drivers
- Open the Run box by pressing Windows key and R together.
- Then, type ‘devmgmt.msc’ and press Enter. It will open the Device Manager window.
- Go to the Batteries and expand it. Under that, right-click on the ‘Microsoft ACPI Compliant Control Method Battery’ listing, and then select ‘Update software driver’.
- If the internet is active, then click on ‘Search automatically for updated driver software’ in the next window. Due to this your device will automatically search the new updates and install them in your system.
Hence, you can resolve the issue of HP laptop plugged in not charging using the above methods and make your laptop charge again correctly like before.